Run FAM & Practical Knowledge

1.

1 point

True or False- A one minute motor is required for ALL engine starts?

True

False

2.

1 point

Augmentor Instability is considered to be present when what 2 conditions exist?

3.

1 point

In Primary mode at Idle, what is the allowable difference between Maximum and Mininum sensors and Average FTIT value? Ref: 2J-F100-41-2

55*

45*

40*

50*

4.

1 point

What is the minimum disengagement clearance between the air Starter Jaw and the engine Gearbox Starter Jaw Coupling?

5/8"

7/16"

1"

1/2"

5.

1 point

Engine Oil System Servicing should be performed wihin how many minutes of engine shutdown?

6.

1 point

Operating procedures, practices, etc. which are not correctly followed will cause serious injury, illness, or death if disregarded are defined as?

Notes

Warnings

Cautions

7.

1 point

Engine Accessories and Rigging Procudures can be found in what TO?

8.

1 point

In which Mode would you start a Preserved engine?

Secondary

Primary

9.

1 point

If an engine has been operated above 700* C what is the minimum cool down period?

10 minutes at idle

15 minutes at idle

20 minutes at idle

5 minutes at idle

10.

1 point

In primary mode at Intermediate, what is the allowable difference between Maximum sensor and Average FTIT value?

75* C

50* C

100* C

200* C

11.

1 point

What unit is adjusted to correct Vertical Misalignment between the starter jaw and starter coupling?

Adjust starter

Adjust wedges on starter drive mount assy.

Adjust cell gear

Adjust buss wheel

12.

1 point

During an engine start in Primary or Secondary mode, when is the starter switch released? Ref: 2J-F100-41-2

When N2 reaches 7000 RPM

When N2 reaches 10000 RPM

When N2 reaches 8000 RPM

When N2 reaches 6000 RPM

13.

1 point

During Core run-in procedures, each line of speed must be attained within +/- what RPM of the target speed? Ref: 2J-F100-41-2

+/- 40 RPM

+/- 80 RPM

+/- 50 RPM

+/- 100 RPM

14.

1 point

During an engine runyou notice that the Main Oil Pressure (MOP) gauge in the test cab is reading incorrectly. What cable and pins would you check first in order to isolate the problem?

J1 Pins 18-20 & 29-30

J2 Pins 18-20 & 29-30

J2 Pins 17-20 & 28-30

J1 Pins 17-20 & 28-30

15.

1 point

When performing an Engine Shutdown Procedure, what N2 RPM is the power lever advanced to?

10,500 - 11,000 RPM for 5-10 seconds

12,500 - 13,000 RPM for 5-10 seconds

11,500 - 12,000 RPM for 5-10 seconds

10,000 - 11,500 RPM for 5-10 seconds

16.

1 point

What is the normal Exhaust Nozzle Position at Idle in Primary Mode?

70-95%

75-95%

65-85%

60-85%

17.

1 point

How many minutes at idle is the engine required to be operated when a preservation (10-10) oil is being used?

18.

1 point

If a Core Run-in test is terminated prior to completion, at what step must the test be resumed?

Restart test from step 1

Continue from where you last left off

19.

1 point

An N2 overspeed has occured. What 5 data recordings are performed by the EDU?

20.

1 point

Name 2 engine symptoms which are present during an Engine Stagnation?

N2 rotor speed decrease, increase in FTIT

N2 rotor speed increase, decrease in FTIT

N1 rotor speed decrease, increase in FTIT

N1 rotor speed increase, decrease in FTIT