secrets 2

your internet facing router is under a DDoS attack. when this happens, you sometimes lose SSH access to the device. Which type of ACL must you use to ensure availability.

after hot swapping an interface module (LP) on a brocade MLXe, the interface module boots up to an interactive state, instead of an active state. what is causing this?

During a BGP neighboring session, a brocade router remains in the active state. what are two explanations for this? (choose two)

your network has gone through a security overview and hardening. your BGP router has now lost connectivity. what is causing this to happen?

you are managing a spanning tree network. a user connects a small switch to a network port causing the network to briefly go down; now all the applications run slow. which feature should you add to the port to resolve this problem

which OSPF router type connects two different areas?

you want to enable OSPF graceful restart on your brocade router. what are two ways to configure this? (choose two)

hello packets are being transmitted by an OSPF router. Which IPv4 multicast address is used?

which bits of an IPv4 multicast address are mapped to bits of a MAC address?

you connect MCT client #1 to two brocade MLXe MCT peers. The ICL link between the MLXe nodes fails. the keepalive VLAN maintains connection between MLXe nodes. Which two statements are true? (choose two)

you have learned a route from RIP and OSPF. you would prefer the RIP route to be active instead of the OSPF route. How would you accomplish this?

two OSPF neighbor routers ware unable to establish an adjacency. which two conditions would cause this issue? (choose two)

in VRRP-E which two statements are true?

referring to the exhibit, which two routers would be ASBRs? (choose two)

your brocade device has two connections to your ISPs and you want to load balance your BGP traffic across the links to ISP1. which brocade routing feature allows this?

you need to monitor the ACL and rate limiting counters. Which two actions show you this information? (choose two)

you have set up a dynamic LAG with four ports. now you want to apply TOS based QoS. Which two statements apply? (choose two)

referring to the exhibit, whiere would you enable IGMP snooping?

which type of LSA is genereated on by an ASBR within a NSSA and only flooded with the same NSSA?

your network has gone through a security overview and hardening. your BGP router has now lost connectivity. what is causing this to happen?

a brocade device automatically configures a link local unicast address for an interface by using which prefix?

your network is connected to two ISPs, ISP1 and ISP2. Since ISP1 is more costly then ISP2 you would like to route all incoming trafficeto go through ISP2. which change would you make to a BGP routing?

how many IPv4 multicast groups use the same Ethernet destination MAC address?

you discover the the brocade fastiron has increased CPU utilization. What are two explanations for this? (choose two)

referring to the exhibit, which router will become the VRRP-E?

users often make the mistake of connecting devices to your network without telling you. you want to prevent spanning tree participation between your network and user devices. Which feature prevents user devices from participating?

referring to the exhibit, how are external routes from the RIP domain advertised into OSPF area 0 (backbone)?

you need to force incoming traffic with an 802.1p value of 5 to the lowest hardware queue on your brocade ICX6430. how would you do this

you are configuring your network to ensure VoIP traffic is always serviced before any other type of traffic. which congestion avoidance algorithm must you use to accomplish this?

in the exhibit, you deployed a pair on new brocade MLXes for your server farm interconnects using MCT with jumbo frames. After you depoloyed the new switches, you establish adjacency on only one of the the links. Which two actions will correct this? (choose two)

you are deploying security methods to allow authorized IP addresses to acces your network. Which two statements are true?

referring to the exhibit, which statement is true?

you are adding a brocade fastiron ICX member to a brocade ICX ironstack. Which two statements are true? (choose two)

which type of OSPF LSA is used to advertise routes into a different area?

you configure brocade MCT between two brocade MLXe chassis. which statement is true?

which type of OSPF router advertises external routes?

referring to the exhibit, router A has EBGP peer connections to routers B, C, and D. router A sets weight = 50 for routes from B, weight = 100 for routes from C, and weight = 150 for routes from D. Which route for network 150.10.1.0/24 will be installed in the IP routing table?

neighbors on a given OSPF network will go through six states on their way to fully becoming synchronized with their routing tables. what is ther proper sequence of the first three states?

Which LSA lists all local active OSPF links and their associated costs?

you have changed the outbound policy on a BGP router. what must you do to apply the changes?

which type of VLANs are supported by brocade devices? (choose three)

you are about to add links to your spanning tree protocol (STP) network. some switches will have multiple links to adjacent switches. you expect STP to manage the topology. Which three actions are performed by the switch? (choose three)

in a VRRP-E which statement is true about the use of a command slow-start 10?

Referring to the exhibit, which statement is true?

you have two routers: R1 and R2, running BGP. R1 is peered to ISP1, R2 is peered to ISP2. you want outbound traffic to use ISP1 and only use ISP2 as a backup. you have created a route map using local preference to accomplish this. Which statement is true about configuring this route map?

you need to route a speific block of addresses through a specific destination. which brocade protocol independent feature would you use?

your network has a mixture of Fast Ethernet, Gigabit Ethernet, and 10 Gigabit Ethernet links. what needs to be done to ensure optimal data routing when using OSPF?