Scene Shop Safety

1.

1 point

Dresses and shorts are acceptable shop wear.

True

False

2.

1 point

Long hair should be pulled back or gathered up.

True

False

3.

1 point

Loose-fitting clothes or jewelry should not be worn in the shop.

True

False

4.

1 point

Sandals, clogs, and open-toed shoes are not acceptable shop wear.

True

False

5.

1 point

Safety goggles should be used whenever cutting, drilling, or sanding.

True

False

6.

1 point

Face shields should be worn when there is danger of kickback or flying particles. They are especially useful when grinding metal.

True

False

7.

1 point

Watching someone weld does not require wearing a mask or shield.

True

False

8.

1 point

Safety glasses and ear bands should always be worn while working in the shop

True

False

9.

1 point

Particle masks should be worn when working with any material that creates dust.

True

False

10.

1 point

Cartridge filter masks should be used with solvents such as spray paint.

True

False

11.

1 point

When you notice another worker or supervisor who is not using the proper safety equipment while using a jigsaw, you should wait until they have finished their cut before interrupting them to reminding them to wear the proper gear unless the issue is life threatening. Tapping them on the shoulder could make them lose control of the saw.

True

False

12.

1 point

When grinding metal the most protection for your hearing is offered by:

hearing bands

ear plugs

safety ear muffs

13.

1 point

When operating the abrasive belt sander, you should wear:

particle mask

eye protection

face shield

earplugs

all of these

14.

1 point

When working below another worker, (i.e. someone working on the catwalks while you are on stage, or someone drilling above you on a ladder) the most important thing for you to wear is:

dust mask

hardhat

loose fitting clothes

15.

1 point

Which of these is a safety precaution for the Radial Arm Saw?

Use safety goggles and face shield. Do not remove guards.

use your right hand to pull the saw and stand to the left of the blade.

Keep your fingers a safe distance from the blade

All of the Above

16.

1 point

Which of these is NOT a safety precaution of the Table Saw?

set the blade to 1/4" above the material being cut

When your hand hits the end of the table with pushing the lumber through the saw, you need to use a "fish" push stick for the rest of the job.

Always use the push stick (fish) to guide the wood through and use help when cutting long pieces

Always unplug the saw when changing the blade or guard

Always use goggles and a face shield

Make sure your footing is secure, eyes on the blade, and others are not distracting your attention

The person receiving should guide and pull the wood past the blade

17.

1 point

Which of these is NOT a safety precaution for the Drill Press?

Always make sure that the drill bit is tightened in the chuck with the chuck key

Use the proper speed for the work. Check with Supervisor.

Always wear safety goggles and do not wear gloves

The wood or steel being drilled should not be secured to the drill press table

18.

1 point

Which of these is NOT a safety precaution for the Hand Circular Saw?

If it does not tighten with the knob, brace the miter guide with a scrap piece of wood and Duct tape.

Always unplug before making blade adjustments

Use a face shield and goggles

Be watchful for a kickback, don't put the saw down until you are sure the blade guard has returned to cover the blade and the blade has stopped

Always put the weight of the saw on the secured side of the cut

set the blade depth 1/4" deeper than the material being cut

19.

1 point

Which is NOT a safety precaution for the Abrasive Belt/Disc-Finishing Sander?

Use the worktable to support your project

Do not adjust the belt without a supervisor present

When possible, keep the push stick sharp.

Use goggles, face shield, and a particle mask

When possible, use the vacuum to suck up dust.

20.

1 point

Which of these is NOT a safety precaution for the Panel Saw?

Make sure the larger section of wood is above the blade when cutting horizontally

Use safety goggles and a face shield

Allow the motor to come to full speed before cutting through work

Hold the work against the fence

Always inspect the work for nails, screws, and staples before starting to cut

Allow the Blade to come to a full stop before removing the work

21.

1 point

Which one is NOT a safety precaution when using the Saber or Jig Saw?

Check the position of the electrical cord.

Tie back long hair

Wrap the speed guide with tape

Wear goggles

22.

1 point

Which is NOT a safety precaution when using the Electric Drill?

Tie back long hair

Use goggles

weight the cord

Tighten chuck with key

23.

1 point

Don't force the tool to work faster than the tool will allow. It is safer to work with the tool and not ______ a job.

Stop

conquer

Quit

Hurry

24.

1 point

Use the right tool for the right task. Using the _____ tool can cause injury to you, damage the project, and damage the tool.

Wrong

blue

screw driver

hammer

25.

1 point

The best remedy for most accidents is _______. Planning ahead means you know what to expect, how to handle an emergency, and are thinking about what might happen.

not to use power tools

Prevention

to make someone else do the job

26.

1 point

When using a fire extinguisher think --> PASS. What does this acronym stand for?

Press, aim, sweep, squeeze

Pull, arrange, signal, stop

Pull, aim, squeeze, sweep

Point, alternate, span, squeeze

27.

1 point

The material safety data sheets (M.S.D.S) provide valuable _____ information. They provide information on hazards present and how to handle emergencies if something goes wrong.

safety

detailed

fun

interesting

28.

1 point

Where can you find ALL of the following safety related items... First-Aid kit, fire blanket, sharps container and the safety log?

Safety center (shelf under time clock)

Paint room

Prop boxes

Backstage

Light Booth

29.

1 point

Which of the following are locations of a fire extinguisher?

Stage Left

Welding area

Paint room

Light gallery

Stage Right

under timmy the timeclock

30.

1 point

The three nearest water supply areas are: The paint room, lobby bathrooms, and the dressing rooms.

True

False

31.

1 point

Where is a fire blanket located

Paint Room

T's office

Light booth

Safety center (under time clock)

32.

1 point

Where is the M.S.D.S book located?

T's office

Dimmer room

Paint Room

Safety center (under time clock)